The short answer
To use capillary matting, lay it on a level, waterproof base, soak it right through, and stand pots directly on it so the compost touches the mat through the drainage holes. Keep the mat damp with trickle lines, a reservoir or a watering can. Plants then draw water up from below. In an HDC trial, capillary matting used about a third of the water of overhead irrigation.
- Pots draw water up from damp matting, so the compost must touch the mat.
- Lay the mat on a level, waterproof base; a 2% fall suits several mat types (HDC).
- Soak new matting right through before use: new mat can be slow to take up water.
- Lots of run-off means the bed is too wet, not that it is working well.
- Lantor and Algon grades are rated for about 2–3 seasons; good care extends life.
What is capillary matting and how does it work?
Capillary matting is a thick, absorbent felt that sits under pots and trays and acts as a shallow, even reservoir. When a pot stands on damp matting, the compost in contact with the mat draws water up through the drainage holes by capillary action: water moves from the wetter mat into the drier compost until the two balance. Each plant takes what it uses, so a thirsty plant draws more than a small one standing next to it.
That is why capillary action matters for container plants. Water reaches the roots from below, the foliage stays dry, and very little runs off the bench. In an HDC-funded trial at HRI Efford, capillary matting used roughly a third of the water of overhead irrigation, and good growth was achieved on all three matting types tested (HNS 107, 2002). Savings depend on the set-up, so treat any single percentage with care.
Matting is rated by how much water it holds, in litres per square metre. 1 L/m² is the same as a 1 mm layer of water spread across the mat. A bench of Lantor 2H, which holds 4 L/m², carries the equivalent of 4 mm of water under every pot.
What do you need to set up a capillary bench?
You need a flat surface, a waterproof base, the matting and a way to keep it wet.
- A level bench or floor. Humps and hollows leave dry patches and puddles. The HDC factsheet on capillary irrigation reports that a 2% slope (a 50 mm fall across a 2.5 m bed) suits several types of matting. Wider beds need a gentler slope or splitting into sections.
- A waterproof base sheet, usually polythene, so water stays in the system.
- The matting, cut to the bench. Don't let it hang over the edges unless you mean it to: an overhang wicks water off the bench and onto the floor.
- A water supply. Trickle lines on top of the mat (HDC found 0.75–1.2 m spacing usually keeps nursery beds evenly moist), a gutter or tray reservoir that the mat dips into, or a watering can on small set-ups.
- An optional cover. Perforated polythene or a black and white film over the mat keeps it clean and cuts algae and rooting into the mat. See the care notes below before you choose one.
How to lay capillary matting: step by step
- Level the bench. Check it with a spirit level and pack out any dips. On long beds, set a slight, even fall towards a drain.
- Lay the base sheet. Cover the bench with polythene, overlapping any joins.
- Cut the matting to size with a sharp knife or heavy scissors. For a reservoir set-up, leave a strip long enough to dip into the gutter or tray.
- Check which side is up. GroundCloud has its spunbond support scrim on the underside. Algon has its easy-clean polypropylene surface on top.
- Soak it through before use. HDC notes that new matting is often water-repellent at first, so wet it thoroughly and press out air pockets until it is evenly dark.
- Lay the water supply. Run trickle lines along the mat, or fill the reservoir.
- Stand the pots and press them down. A slight twist helps the compost meet the mat. Water each pot from above once at the start so the compost is already moist and can draw from the mat; the RHS advises this especially for clay pots.
- Watch the run-off. The HNS 107 trial report notes that significant run-off usually means the bed is being run too wet. Cut back until the mat is damp rather than flooded.
Using capillary matting in a greenhouse, for seedlings or while you are away
The same principle works on a small scale. For seed trays and modules in a greenhouse, lay matting on polythene-covered staging or in a solid tray, let one end dip into a reservoir such as a length of gutter or a second tray, and stand the trays directly on the mat. Watering from below keeps the compost surface evenly moist without washing seed about. Top up the reservoir, not the trays.
For watering plants automatically while you are away, the RHS suggests laying capillary matting on a draining board or beside the bath, with one end dipping into the filled sink or bath. Group the pots on the wet mat and press them down slightly. The RHS notes the method may not work for pots with broken crocks in the base, because the crocks stop the compost touching the mat, and that clay pots need a thorough watering first. A single large pot can be fed by a strip of matting used as a wick from a bucket of water. An offcut of Lantor 1H or 2H suits a watering tray or greenhouse staging.
Which capillary matting should I use?
Match the grade to where it will sit and how much water you want in reserve. Heavier, thicker grades hold more and suit floor-level beds; the HDC factsheet also prefers thicker grades at floor level.
| Situation | Grade to start with | Why |
|---|---|---|
| Indoor nursery or garden-centre benches | Lantor 2H: 300 g/m², 4 L/m², 4 mm | Indoor grade with a good water reserve |
| Light indoor benches, small pots | Lantor 1H: 250 g/m², about 2.5–3 L/m², 3 mm | Lighter, thinner mat |
| Retail display where looks matter | Algon 2H: 350 g/m², about 3 L/m² | Easy-clean polypropylene top surface |
| Floor level or outdoor standing areas | Lantor 4H or Algon 4H: 8 mm, 5 L/m² | Thickest grades, highest water holding |
| Large areas or non-standard widths | GroundCloud Purple: 275 g/m², 3.5 L/m² | 1–2 m wide as standard, 0.5–4.3 m to order |
| Living walls fed from a reservoir | Lantor AP200 Black wicking felt | Thin polyester felt with around 100–110 mm capillary rise after 4 hours |
For a full side-by-side comparison, including the easy-clean and wicking grades, read which capillary matting? Grades compared.
How long does capillary matting last?
We rate the Lantor and Algon grades at about 2–3 seasons, depending on the site. The HDC factsheet says matting typically needs replacing at around 5-year intervals where matting alone is used, longer if well maintained, and that better-quality mats last longer under protection if carefully managed. The gap comes down to conditions: covered benches under glass with soft water and regular flushing at one end, open outdoor beds with hard water at the other.
To get the most from a mat:
- Don't let it dry out completely. Dry matting is hard to re-wet.
- Flush it with plain water now and then to stop fertiliser salts building up. HDC notes that high salts and bicarbonate make mats hard and water-repellent, and suggests acidifying the supply in hard-water areas.
- Think before covering it. Permeable covers keep the mat clean, reduce weeds and rooting through, and prolong its life. But HDC found they can reduce capillary contact, and small 9 cm pots were more affected than 3 litre containers.
- Change polythene covers between crops for hygiene.
What are the disadvantages of capillary matting?
Capillary matting is not right for every bench, and it helps to know the drawbacks before you buy.
- Algae. University of Nebraska–Lincoln Extension notes that light-coloured mats tend to develop algae, and that pots spaced apart on open mat lead to algae and fungus gnats. A black and white film laid black side down, with holes cut for the pots, blocks light to the mat and cuts evaporation (EC303).
- Salt build-up, especially with hard water (see above).
- Roots growing into the mat on long crops, which a cover reduces.
- It needs level ground and good contact. Crocks, thick-based pots or a warped bench break the capillary link.
- It can sit too wet outdoors in winter. HDC says robust mats can be used outdoors in well-drained situations, but are mainly used under protection for this reason.
Alternatives include sand beds and flood-and-drain benches, which HDC groups with matting as low-level systems that use less water than overhead sprinklers, and drip irrigation. As a short-term DIY fix, the RHS mentions wet towels for houseplants. Purpose-made matting gives a stated, even water holding per m², which household fabrics can't.
Products mentioned
Lantor 2H300 g/m² · 4 L/m² · 4 mm
GroundCloud Purple275 g/m² · 3.5 L/m² · 4 mm
Lantor 4H550 g/m² · 5 L/m² · 8 mm
Algon 2H350 g/m² · c. 3 L/m² · 3.5 mm
Sources
- AHDB (HDC) — Factsheet 01/06: Capillary irrigation of container grown nursery stock (2006)
- AHDB (HDC) — HNS 107: Capillary matting trial, HRI Efford, annual report (2002)
- University of Nebraska–Lincoln Extension — EC303: Constructing a growing bench for capillary mat irrigation (2014)
- RHS — Houseplants: holiday care (checked 2026)





